IR 192 Gamma ray source radiographic inspection is offered to inspect welding at the manufacturing facilities of fabricators & foundries, as well as during construction of thermal power plant, refineries and petrochemical plants.

Ultrasonic Flaw Detection: Our ASNT Level II certified technicians are equipped with digital flaw detectors for greater reliability & faster examination when manual scanning of welds, castings, forgings & plates is to be carried out.

Ultrasonic thickness measurement is carried out for assessing corrosion in process plant, piping & equipment. AITIS instruments have latest through coat technology, making it unnecessary to remove paint from the surface from which measurement is carried out. Data logger and a variety of software are used to produce reports which form a useful database for tracking corrosion.

The following MPI techniques are offered; Yoke type, prod type and coil type magnetizing equipment, dry powder, wet magnetic particles & wet fluorescent magnetic particle technique mainly using for Castings, forgings, welds, turbines & the components of rotating machinery to check Surface / Sub Surface Cracks etc.

Liquid penetrate inspection (PT) is one of the most widely used nondestructive evaluation (NDT) methods. Its popularity can be attributed to two main factors, its relative ease of use and its flexibility.All types of Fluorescent Penetrates and Visible Penetrates are used to inspect materials include the following; Metals (aluminium, copper, steel, titanium, etc.), Glass, Ceramic materials, Rubber and Plastics.

Visual testing is used for the detection of surface flaws and discontinuities. The effectiveness of the technique can be enhanced through the aid of such tools as mirrors, magnifiers, fiberscopes, etc. Quantification of indications can be augmented through the use of tools such as depth gauges, templates, displacement gauges, etc. AITIS team for Visual Inspectors are Certified and Experienced as well. We have a number of Certified Visual Inspector from ASNT, API, CSWIP / AWS, NACE and BGAS.

Quick, Reliable, Durable & Proven Design. It is virtually foolproof and indestructible. Seal off one end of the suspect tube(s) with either a rubber tube plug or the T-Handle with an attached nozzle; then insert the Vacuum Leak Detector into tube to be tested and depress the trigger, a loss of vacuum indicates a leaking tube. It has a filter system to prevent debris inside the tube from clogging the tool.

It is used to inspect the tube to tube sheet area. Tests rolled or welded tube sheet joints by vacuum pressure. Insert nozzle into the tube and press face of the gun into the clean tube sheet joint being tested. Actuate gun to generate the vacuum, if pressure fails to hold...there is a leak.

Visual testing is used for the detection of surface flaws and discontinuities. The effectiveness of the technique can be enhanced through the aid of such tools as mirrors, magnifiers, fiberscopes, etc. Quantification of indications can be augmented through the use of tools such as depth gauges, templates, displacement gauges, etc. AITIS team for Visual Inspectors are Certified and Experienced as well. We have a number of Certified Visual Inspector from ASNT, API, CSWIP / AWS, NACE and BGAS.

Advantages

The technique is portable and can be used on-site.

Portable hardness can also be used to monitor hardness of purchased components.

The hardness technique can be applied to wide variety of materials. Like all ferrous and non ferrous and alloys.

The technique is useful where elevated temperature components used at high stresses (turbine rotor / discs, steam piping, heat exchanger, pressure vessels, etc.).

Application

To check the hardness of heat treated part and to verify the heat treatment Process.

Portable Hardness testing of various metals & alloys in different forms such as castings, forgings, pipes, plates etc. non-destructively & at site.

Life assessment of equipment & components used in service at high temperature & under high stress / pressure (like reactors, furnace tubes, turbine shaft, turbine discs, gas pipe lines etc.)

Eddy Current Testing (ECT) is an electromagnetic non destructive testing Technique widely used in Power Plants, Petro- Chemical, Refineries and other Industries.

AITIS Equipped with latest Eddy current Equipments

High Examination Rate (80 - 100 or more tubes Inspection per hour).

ECT has high deductibility for all non-ferromagnetic materials

Repeatability - compare historical and subsequent test results to establish corrosion rates and remaining life.

ECT discriminates between I.D and O.D. defect.

ECT is sensitive to gradual wall loss, cracking, very small pitting etc.

AITIS uses advanced RFET/NFT equipments and techniques for Carbon steel.

Ideal for ferrous tubes (Boiler tubes)

It can detect defects from Under Tube support plate.

Detect localizes corrosion/erosion

Inspects ferromagnetic materials (Carbon steel and Stainless Steel)

Detect wall loss

Can inspect tubes up to 75mm OD with 5mm thickness.

AITIS have the latest version TELETEST Equipment in GUIDED WAVE

LRUT is traditionally used to detect corrosion, erosion and other defects in pipe work. An array of transducers is clamped around the pipe and ultrasound is transmitted simultaneously along the pipe in both directions. The return signal is received by the same transducers, and the data are analyzed using the system's calibrated software.

AITIS SERVICES IN GUIDED WAVE

Inspect internal and external corrosion

Painted pipe work

Road crossing

Bund wall penetration

Buried pipelines

High temperature lines

Sleeves section

Inspect 2 inch to 48inch pipe dia

It has the versatility to work with all dual gate UT meters.

GUIDED WAVE ADVANTAGES

Inspect pipes in the working condition

Single position we can inspect 80m both direction

No need to remove insulation (Need one meter for probe fixing)

Faults in rotating machinery are identified and then root causes are analyzed, so that it can be fixed at once

AITIS technicians are equipped with CSI 2130 Machinery Health Analyzer which is the industry leading Vibration data collector with its advanced features the following can be perform

Above Ground Storage Tank Inspection

Low Frequency Electromagnetic Technique (LFET) are used to inspect storage tanks, other convex or concave ferrous surfaces, as well as nonferrous metal tubing/piping surfaces. It is used for detecting wall thickness changes in carbon steel storage tank floor plates. Low Frequency Electromagnetic Technique (LFET) products does not use permanent magnets, so are lightweight (under 30 lbs) and are is easy to handle and transport.LFET-based tests require minimal floor preparation; it tests through coatings and determines top surface flaws from bottom surface flaws.

It s very accurate. Wall thickness measurements can be made, with the use of a 15MHz-focused transducer, to an accuracy of within 0.1mm. IRIS is an ultrasonic based system for inspecting ferrous and nonferrous tubes from the inside. It is applied on almost any material. With the IRIS, accurate thickness measurementscan be taken at any location along the tube, so small changes in thickness are measurable and the exact location of pitting and corrosion can be determined. It is a fairly sensitive technique. The sensitivity achieved will depend on tube dimensions and tube cleanliness. In general, it can be stated that, it should be possible to detect a 1.5mm defect in tubing up to 1 inch which has been properly cleaned.Both ferromagnetic and non-ferromagnetic tubes can be inspected A three dimensional picture of the defect is obtained, thus the defect profile and its depth is provided.

Above Ground Storage Tank Inspection

Viper system are used to inspect ferrous structure that have a limited access using ultrasonic. The viper is a remote access ultrasonic crawler designed to allow cost effective ultrasonic inspections on above ground ferromagnetic structures as oil storage tanks without the need for costly scaffolding or rope access

Advantages

The viber crawler has the ability to inspect remote areas within 100ft of the inspection personnel.

It has the versatility to work with all dual gate UT meters.

We are equipped with Fibro scope (Video scope- Gradient Lens) to perform internal & visual Inspection

Boiler Tubes

Internal components of Centrifugal pump

Heat Exchanges Tubes

Motor Windings

Positive Material Identification (PMI) is portable technique used to determine the chemical composition of ferrous and non ferrous metals alloys. The technique is used non-destructively to obtain accurate results.

AITIS provides Positive Material Identification on the followin

To verify that all critical materials conform to project requirements.

To verify the alloy grade.

To sort the different alloys and grades which are mixed together

To identify the alloy grade and specific elements composition.

AITIS provides the services in Oil & Gas, Chemical, Cement, Iron & Steel, Fertilizers, and Aluminum plants etc.

Metallography or microscopy consists of microscopic study of the structural constituents (i.e. Ferrite, Pearlite, Carbide, Austenite, etc.) of metals or an alloy by optical microscope or an electron microscope. In metallography, we also study the relation of structure to properties of metals or alloys.

Advantages

The technique is portable and can be used on-site.

Field Metallography can also be used to monitor quality of purchased components.

Field Metallography can be used to monitor the evolution of micro structural changes in components during lifetime.

This is particularly useful in assessing creep damage in elevated temperature components ( turbine rotor / discs, steam piping, heat exchanger, chemical reactor, pressure vessels, etc.)

The technique can be applied to a wide variety of materials.

Field Metallography can complement nondestructive techniques such as ultrasonic testing.

Holiday test is one of the Non - destructive test method applied on protective coatings to detect unacceptable discontinuities such as pin holes and voids. The test involves checking of an electric circuit to see if current flows to complete the electrical circuit.

Holiday test is performed by applying low voltage across the choosen path.

The Machine is a compact and lightweight instrument, which can easily be carried by the operator with the supplied Neck Strap

AITIS has certified by Lifting Equipment Engineers Association (LEEA) to conduct inspection in all lifting equipments such as Overhead Crane, Mobile Crane, etc.

AITIS has qualified and trained inspectors to do all lifting equipment inspection.

The health of equipment is inspected by the procedure of LEEA which includes visual, NDT, functional test and load test.

AITIS equipped with different loads, load shackles and slings to conduct the load test for all types of cranes.

AITIS offers Preheat/ Post weld heat treatment services for the stress reliving of welds and heat affected zone.

Preheating

Preheating of the weldment area achieves better weld penetration and slows the cooling process, thus allowing added relief of stresses and reduced hardening of the materials.

Post weld Heat Treatment

As a result of welding processes used to join metals together, the base materials near the weldment, the deposited weld metal and, in particular, the heat affected zones transform through various metallurgical phases. Depending upon the chemistry of the metals in these areas, hardening occurs in various degrees, dependent mainly upon carbon content. Again, this is particularly true in the heat affected zone (HAZ) adjacent to the weld metal deposit where the highest stresses due to melting and solidification result. PWHT, is designed to relieve a proportion of these imposed stresses by reducing the hardness and increasing ductility, thus reducing danger of cracking in the vessel weldments.

AITIS equipped with advanced automated Heat Treatment equipment and we are executing the job with highly qualified and experienced person to meet all kind of client requirement.

AITIS provides highly quality Heat treatment services with safety and on time.

Boiler Condition assessment

Boiler life assessment

Failure Analysis

API-510 Pressure vessel inspection

API-653 Tank inspection

The Falcon S Series is a tank floor scanner based on Saturation Low Frequency Eddy Current Technique. It scans tank floors by saturating the floor plates with an electromagnet and then using Eddy Current to detect defects in the plate as it scans over it. With this technique we are able to detect pits, holes, cracking, and wall loss while differentiating the orientation of the flaw depending on if it is a top side or bottom side flaw. The highly sensitive nature of eddy current allows the scanner to detect and size top side and bottom side pitting, and localized wall loss. Additionally, The Falcon S Series can detect cracks. Falcon S Series to scan through non-metallic coatings of up to 0.5 in. (12mm)

AITIS ( Abdallah Ibrahim Altamimi Industrial Services ) is founded with the mission to provide Inspection, Verification & Testing Services with quality and integrity. Our expertise is in Inspection, Testing, Advanced NDT, Condition assessment and remaining life assessment. AITIS is dealing with inspection of Boilers, Heat Exchangers, Pressure Vessels, Plant Piping, Tanks, Furnaces, Reactors, Turbines, Turbine blades and Turbine routers. AITIS is providing state of the art advance Inspection technology to the Desalination , Oil and Gas Sector, Power Sector, Refineries and Chemical Plants. AITIS is ISO 9001:2015 Certified Company and is also a Corporate member of ASNT.

We aim to be the most competitive and the most productive service organization in the Kingdom and GCC. Our core competencies in inspection, verification and testing are being continuously improved to be best-in-class. Our chosen markets will solely be determined by our ability to be the most competitive and to consistently deliver unequalled service to our customers all over the GCC.

Our Values

We seek to be epitomized by our passion, integrity and our innovative spirit, as we continually strive to fulfill our vision. These values guide us in all that we do and are the bedrock upon which our organization is built. AITIS is ISO 9001:2015 Certified Company. We are also the Corporate member of ASNT,LEEA, PIPE SURVEY INTERNATIONAL and M&M ENGINEERING ASSOCIATES

Our Services

AITIS has the qualification and ability to perform all Conventional and Advance NDT techniques with highly distinguished level of quality.AITIS is using the latest models of instruments and materials in inspection and testing. AITIS is following International code and standards of ASME, API, NACE, BGAS and ASNT in daily inspections.